CoRE Working Group M. Tiloca Internet-Draft RISE SICS AB Intended status: Standards Track G. Selander Expires: September 14, 2017 F. Palombini Ericsson AB March 13, 2017 Secure group communication for CoAP draft-tiloca-core-multicast-oscoap-01 Abstract This document describes a method for application layer protection of messages exchanged with the Constrained Application Protocol (CoAP) in a group communication context. The proposed approach relies on Object Security of CoAP (OSCOAP) and the CBOR Object Signing and Encryption (COSE) format. All security requirements fulfilled by OSCOAP are maintained for multicast CoAP request messages and related unicast CoAP response messages. Source authentication of all messages exchanged within the group is ensured, by means of digital signatures produced through asymmetric private keys of sender devices and embedded in the protected CoAP messages. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on September 14, 2017. Copyright Notice Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents Tiloca, et al. Expires September 14, 2017 [Page 1] Internet-Draft Secure group communication for CoAP March 2017 (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 2. Requirements . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Scope Description . . . . . . . . . . . . . . . . . . . . . . 7 4. Security Context . . . . . . . . . . . . . . . . . . . . . . 8 5. The COSE Object . . . . . . . . . . . . . . . . . . . . . . . 9 6. Message Processing . . . . . . . . . . . . . . . . . . . . . 10 6.1. Protecting the Request . . . . . . . . . . . . . . . . . 10 6.2. Verifying the Request . . . . . . . . . . . . . . . . . . 10 6.3. Protecting the Response . . . . . . . . . . . . . . . . . 11 6.4. Verifying the Response . . . . . . . . . . . . . . . . . 11 7. Security Considerations . . . . . . . . . . . . . . . . . . . 12 7.1. Group-level Security . . . . . . . . . . . . . . . . . . 12 7.2. Management of Group Keying Material . . . . . . . . . . . 12 7.3. Late Joining Endpoints . . . . . . . . . . . . . . . . . 13 7.4. Provisioning of Public Keys . . . . . . . . . . . . . . . 13 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14 9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 14 10. References . . . . . . . . . . . . . . . . . . . . . . . . . 14 10.1. Normative References . . . . . . . . . . . . . . . . . . 14 10.2. Informative References . . . . . . . . . . . . . . . . . 15 Appendix A. Group Joining Based on the ACE Framework . . . . . . 16 Appendix B. List of Use Cases . . . . . . . . . . . . . . . . . 17 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 19 1. Introduction The Constrained Application Protocol (CoAP) [RFC7252] is a web transfer protocol specifically designed for constrained devices and networks. [RFC7390] enables group communication for CoAP, addressing use cases where deployed devices benefit from a group communication model for example to limit latencies and improve performance. Use cases include lighting control, integrated building control, software and firmware updates, parameter and configuration updates, commissioning of constrained networks, and emergency multicast. [RFC7390] Tiloca, et al. Expires September 14, 2017 [Page 2] Internet-Draft Secure group communication for CoAP March 2017 recognizes the importance to introduce a secure mode for CoAP group communication. This specification defines such a mode. Object Security of CoAP (OSCOAP)[I-D.ietf-core-object-security] describes a security protocol based on the exchange of protected CoAP messages. OSCOAP builds on CBOR Object Signing and Encryption (COSE) [I-D.ietf-cose-msg] and provides end-to-end encryption, integrity, and replay protection across intermediate modes. To this end, a CoAP message is protected by including payload (if any), certain options, and header fields in a COSE object, which finally replaces the authenticated and encrypted fields in the protected message. This document describes multicast OSCOAP, providing end-to-end security of CoAP messages exchanged between members of a multicast group. In particular, the described approach defines how OSCOAP should be used in a group communication context, while fulfilling the same security requirements. That is, end-to-end security is assured for multicast CoAP requests sent by multicaster nodes to the group and for related unicast CoAP responses sent as reply by multiple listener nodes. Multicast OSCOAP provides source authentication of all CoAP messages exchanged within the group, by means of digital signatures produced through asymmetric private keys of sender devices and embedded in the protected CoAP messages. As in OSCOAP, it is still possible to simultaneously rely on DTLS to protect hop-by-hop communication between a multicaster node and a proxy (and vice versa), and between a proxy and a listener node (and vice versa). 1.1. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. These words may also appear in this document in lowercase, absent their normative meanings. Readers are expected to be familiar with the terms and concepts described in [RFC7252], [RFC7390] and [RFC7641]. Terminology for constrained environments, such as "constrained device", "constrained-node network", is defined in [RFC7228]. Terminology for protection and processing of CoAP messages through OSCOAP, such as "Security Context", "Master Secret", "Master Salt", is defined in [I-D.ietf-core-object-security]. This document refers also to the following terminology. Tiloca, et al. Expires September 14, 2017 [Page 3] Internet-Draft Secure group communication for CoAP March 2017 o Keying material: data that is necessary to establish and maintain secure communication among member of a multicast group. This includes, for instance, keys, key pairs, and IVs [RFC4949]. o Group Manager (GM): entity responsible for creating a multicast group, establishing and provisioning security contexts among authorized group members, and managing the joining of new group members. A GM can be responsible for multiple multicast groups, while it is not required to be an actual group member and to take part in the group communication. The GM may also be responsible for renewing/updating security contexts and related keying material. Any message exchange with the GM MUST be secured and based on different secure channels for different endpoints. o Multicaster: member of a multicast group that sends multicast CoAP messagges intended for all members of the group. In a 1-to-N multicast group, only a single multicaster transmits data to the group; in an M-to-N multicast group (where M and N do not necessarily have the same value), M group members are multicasters. o Listener: member of a multicast group that receives multicast CoAP messages when listening to the multicast IP address associated to the multicast group. A listener MAY reply back, by sending a unicast response message to the multicaster which has sent the multicast message. o Group request: multicast CoAP request message sent by a multicaster in the group to all listeners in the group through multicast IP. o Group response: unicast CoAP response message sent back by a listener in the group as a response to a group request received from a multicaster. o Source authentication: evidence that a received message in the group originated from a specifically identified group member. This also provides assurances that the message was not tampered with by any other group member or an adversary outside the group. 2. Requirements The following security requirements are out of the scope of this document and are assumed to be already fulfilled. o Establishment and management of a security context: a security context must be established among the group members by the Group Manager which manages the multicast group. A secure mechanism Tiloca, et al. Expires September 14, 2017 [Page 4] Internet-Draft Secure group communication for CoAP March 2017 must be used to generate, revoke and (re-)distribute keying material, multicast security policies and security parameters in the multicast group. The actual establishment and management of the security context is out of the scope of this document, and it is anticipated that an activity in IETF dedicated to the design of a generic key management scheme will include this feature, preferably based on [RFC3740][RFC4046][RFC4535]. o Multicast data security ciphersuite: all group members MUST agree on a ciphersuite to provide authenticity, integrity and confidentiality of messages in the multicast group. The ciphersuite is specified as part of the security context. o Backward security: a new device joining the multicast group should not have access to any old security contexts used before its joining. This ensures that a new group member is not able to decrypt confidential data sent before it has joined the group. The adopted key management scheme should ensure that the security context is updated to ensure backward confidentiality. The actual mechanism to update the security context and renew the group keying material upon a group member's joining has to be defined as part of the group key management scheme. o Forward security: entities that leave the multicast group should not have access to any future security contexts or message exchanged within the group after their leaving. This ensures that a former group member is not able to decrypt confidential data sent within the group anymore. Also, it ensures that a former member is not able to send encrypted and/or integrity protected messages to the group anymore. The actual mechanism to update the security context and renew the group keying material upon a group member's leaving has to be defined as part of the group key management scheme. The following security requirements need to be fulfilled by the approach described in this document: o Multicast communication topology: this document considers both 1-to-N (one multicaster and multiple listeners) and M-to-N (multiple multicasters and multiple listeners) communication topologies. The 1-to-N communication topology is the simplest group communication scenario that would serve the needs of a typical LLN. For instance, in the lighting control use case, switches are the only entities responsible for sending commands to a group of lighting devices. In more advanced lighting control use cases, a M-to-N communication topology would be required, for instance in case multiple sensors (presence or day-light) are responsible to trigger events to a group of lighting devices. Tiloca, et al. Expires September 14, 2017 [Page 5] Internet-Draft Secure group communication for CoAP March 2017 o Multicast group size: security solutions for group communication SHOULD be able to adequately support different, possibly large, group sizes. Group size is the combination of the number of multicasters and listeners in a multicast group, with possible overlap (i.e. a multicaster MAY also be a listener at the same time). In the use cases mentioned in this document, the number of multicasters (normally the controlling devices) is expected to be much smaller than the number of listeners (i.e. the controlled devices). A security solution for group communication that supports 1 to 50 multicasters would be able to properly cover the group sizes required for most use cases that are relevant for this document. The total number of group members is expected to be in the range of 2 to 100 devices. Groups larger than that SHOULD be divided into smaller independent multicast groups, e.g. by grouping lights in a building on a per floor basis. o Data replay protection: it MUST NOT be possible to replay a group request message or a group response message, which would disrupt the correct communication in the group and the activity of group members. o Group-level data confidentiality: messages sent within the multicast group SHALL be encrypted. In fact, some control commands and/or associated responses could pose unforeseen security and privacy risks to the system users, when sent as plaintext. In particular, data confidentiality MAY be required if privacy sensitive data is exchanged in the group. This document considers group-level data confidentiality since messages are encrypted at a group level, i.e. in such a way that they can be decrypted by any member of the multicast group, but not by an external adversary or other external entities. o Source authentication: messages sent within the multicast group SHALL be authenticated. That is, it is essential to ensure that a message is originated by a member of the group in the first place (group authentication), and in particular by a specific member of the group (source authentication). The approach proposed in this document provides both group authentication and source authentication, both for group requests originated by multicasters and group responses originated by listeners. In order to provide source authentication, outgoing messages are signed by the respective originator group member by means of its own asymmetric private key. The resulting signature is included in the COSE object. o Message integrity: messages sent within the multicast group SHOULD be integrity protected. That is, it is essential to ensure that a message has not been tampered with by an external adversary or Tiloca, et al. Expires September 14, 2017 [Page 6] Internet-Draft Secure group communication for CoAP March 2017 other external entities which are not group members. Message integrity is provided through the same means used to provide source authentication. 3. Scope Description An endpoint joins a multicast group by explicitly interacting with the responsible Group Manager. The actual join process MAY be based on the ACE framework [I-D.ietf-ace-oauth-authz] and the OSCOAP profile of ACE [I-D.seitz-ace-oscoap-profile], as discussed in Appendix A. An endpoint registered as member of a group can behave as a multicaster and/or as a listener. As a multicaster, it can transmit multicast request messages to the group. As a listener, it receives multicast request messages from any multicaster in the group, and possibly replies by transmitting unicast response messages. A number of use cases that benefit from secure group communication are discussed in Appendix B. Upon joining the group, endpoints are not required to know how many and what endpoints are active in the same group. An endpoint which is registered as member of a group is identified by an endpoint ID, which is not necessarily related to any protocol- relevant identifiers, such as IP addresses. The Group Manager generates and manages endpoint IDs in order to ensure their uniqueness within a same multicast group. That is, there cannot be multiple endpoints that belong to the same group and are associated to a same endpoint ID. In order to participate in the secure group communication, an endpoint needs to maintain additional information elements, stored in its own security context. Those include keying material used to protect and verify group messages, as well as the public keys of other endpoints in the groups, in order to verify digital signatures of secure messages and ensure their source authenticity. These pieces of information are provided by the Group Manager through out- of-band means or other pre-established secure channels. Further details about establishment, revocation and renewal of the security context and keying material are out of the scope of this document. According to [RFC7390], any possible proxy entity is supposed to know about the multicasters in the group and to not perform aggregation of response messages. Also, every multicaster expects and is able to handle multiple unicast response messages associated to a given multicast request message. Tiloca, et al. Expires September 14, 2017 [Page 7] Internet-Draft Secure group communication for CoAP March 2017 4. Security Context To support multicast communication secured with OSCOAP, each endpoint registered as member of a multicast group maintains a Security Context as defined in Section 3 of [I-D.ietf-core-object-security]. In particular, each endpoint in a group stores: 1. one Common Context, received from the Group Manager upon joining the multicast group and shared by all the endpoints in the group. The Common Context contains the COSE AEAD algorithm, the Master Secret and, optionally, the Master Salt used to derive endpoint- based keying material (see Section 3.2 of [I-D.ietf-core-object-security]). All the endpoints in the group agree on the same COSE AEAD algorithm. Besides, in addition to what is defined in [I-D.ietf-core-object-security], the Common Context stores the following parameters: * Context Identifier (Cid). Variable length byte string that identifies the Security Context. The Cid used in a multicast group is determined by the responsible Group Manager and does not change over time. A Cid MUST be unique in the sets of all the multicast groups associated to the same Group Manager. The choice of the Cid for a given group's Security Context is application specific, but it is RECOMMENDED to use 64-bit long pseudo-random Cids, in order to have globally unique Context Identifiers. It is the role of the application to specify how to handle possible collisions. * Counter signature algorithm. Value that identifies the algorithm used for source authenticating messages sent within the group. Its value is immutable once the security context is established. All the endpoints in the group agree on the same counter signature algorithm. 2. one Sender Context, used to secure outgoing messages. In particular, the Sender Context is initialized according to Section 3 of [I-D.ietf-core-object-security], once the endpoint has joined the multicast group. Besides, in addition to what is defined in [I-D.ietf-core-object-security], the Sender Context stores also the endpoint's asymmetric public-private key pair; 3. one Recipient Context for each distinct endpoint from which messages are received, used to process such incoming secure messages. The endpoint creates a new Recipient Context upon receiving an incoming message from another endpoint in the group for the first time. Besides, in addition to what is defined in [I-D.ietf-core-object-security], each Recipient Context stores also the public key of the associated other endpoint from which Tiloca, et al. Expires September 14, 2017 [Page 8] Internet-Draft Secure group communication for CoAP March 2017 secure messages are received. Possible approaches to provision and retrieve public keys of group members are discussed in Section 7.4. The Sender Key/IV stored in the Sender Context and the Recipient Keys/IVs stored in the Recipient Contexts are derived according to the same scheme defined in Section 3.2 of [I-D.ietf-core-object-security]. The 3-tuple (Cid, Sender ID, Partial IV) is called Transaction Identifier (Tid), and SHALL be unique for each Master Secret. The Tid is used as a unique challenge in the COSE object of the protected CoAP request. The Tid is part of the Additional Authenticated Data (AAD, see Section of 5.2 of [I-D.ietf-core-object-security]) of the protected CoAP response message, which is how unicast responses are bound to multicast requests. 5. The COSE Object When creating a protected CoAP message, an endpoint in the group computes the COSE object as defined in Section 5 of [I-D.ietf-core-object-security], with the following modifications. 1. The value of the "Partial IV" parameter in the "protected" field is set to the Sequence Number and SHALL be present in both multicast requests and unicast responses. Specifically, a multicaster endpoint sets the value of "Partial IV" to the Sequence Number from its own Sender Context, upon sending a multicast request message. Similarly, a listener endpoint sets the value of "Partial IV" to the Sequence Number from its own Sender Context, upon sending a unicast response message. 2. The value of the "kid" parameter in the "protected" field is set to the Sender ID of the endpoint and SHALL be present in both multicast requests and unicast responses. 3. The "protected" field of the "Headers" field SHALL include also the following parameter: * gid : its value is set to the Context Identifier (Cid) of the group's Security Context. This parameter is optional if the message is a CoAP response. 4. The Additional Authenticated Data (AAD) considered to compute the COSE object is extended. In particular, the "external_aad" considered for secure response messages SHALL include also the following parameter: Tiloca, et al. Expires September 14, 2017 [Page 9] Internet-Draft Secure group communication for CoAP March 2017 * cid : bstr, contains the Context Idenfier (Cid) of the Security Context considered to protect the request message (which is same as the Cid considered to protect the response message). 5. Before transmitting any secure CoAP message, the sender endpoint uses its own private key to create a counter signature of the COSE_Encrypt0 object (Appendix C.4 of [I-D.ietf-cose-msg]). Then, the counter signature is included in the Header of the COSE object in its "unprotected" field. 6. Message Processing Each multicast request message and unicast response message is protected and processed as specified in [I-D.ietf-core-object-security], with the modifications described in the following sections. Furthermore, error handling and processing of invalid messages are performed according to the same principles adopted in [I-D.ietf-core-object-security]. 6.1. Protecting the Request A multicaster endpoint transmits a secure multicast request message as described in Section 7.1 of [I-D.ietf-core-object-security], with the following modifications: 1. The multicaster endpoint stores the association Token - Cid. That is, it SHALL be able to find the correct Security Context used to protect the multicast request and verify the unicast response(s) by using the CoAP Token considered in the message exchange. 2. The multicaster endpoint computes the COSE object as defined in Section 5 of this specification. 6.2. Verifying the Request Upon receiving a secure multicast request message, a listener endpoint proceeds as described in Section 7.2 of [I-D.ietf-core-object-security], with the following modifications: 1. The listener endpoint retrieves the Context Identifier from the "gid" parameter of the received COSE object, and uses it to identify the correct group's Security Context. 2. The listener endpoint retrieves the Sender ID from the header of the COSE object. Then, the Sender ID is used to retrieve the correct Recipient Context associated to the multicaster endpoint and used to process the request message. When receiving a secure Tiloca, et al. Expires September 14, 2017 [Page 10] Internet-Draft Secure group communication for CoAP March 2017 multicast CoAP request message from that multicaster endpoint for the first time, the listener endpoint creates a new Recipient Context, initializes it according to Section 3 of [I-D.ietf-core-object-security], and includes the multicaster endpoint's public key. 3. The listener endpoint retrieves the corresponding public key of the multicaster endpoint from the associated Recipient Context and uses it to verify the counter signature, before proceeding with the verification and decryption of the secure request message. 6.3. Protecting the Response A listener endpoint that has received a multicast request message MAY reply with a secure unicast response message, which is protected as described in Section 7.3 of [I-D.ietf-core-object-security], with the following modifications: 1. The listener endpoint considers the Transaction Identifier (Tid) as defined in Section 4 of this specification. 2. The listener endpoint computes the COSE object as defined in Section 5 of this specification. 6.4. Verifying the Response Upon receiving a secure unicast response message, a multicaster endpoint proceeds as described in Section 7.4 of [I-D.ietf-core-object-security], with the following modifications: 1. The multicaster endpoint considers the Security Context identified by the Token of the received response message. 2. The multicaster endpoint retrieves the Sender ID from the header of the COSE object. Then, the Sender ID is used to retrieve the correct Recipient Context associated to the listener endpoint and used to process the response message. When receiving a secure CoAP response message from that listener endpoint for the first time, the multicaster endpoint creates a new Recipient Context, initializes it according to Section 3 of [I-D.ietf-core-object-security], and includes the listener endpoint's public key. 3. The multicaster endpoint retrieves the corresponding public key of the listener endpoint from the associated Recipient Context and uses it to verify the counter signature, before proceeding Tiloca, et al. Expires September 14, 2017 [Page 11] Internet-Draft Secure group communication for CoAP March 2017 with the verification and decryption of the secure response message. The mapping between unicast response messages from listener endpoints and the associated multicast request message from a multicaster endpoint relies on the same principle adopted in [I-D.ietf-core-object-security]. That is, it is based on the Transaction Identifier (Tid) associated to the secure multicast request message, which is considered by listener endpoints as part of the Additional Authenticated Data when protecting their own response message. 7. Security Considerations Specific security aspects to be taken into account are discussed below. 7.1. Group-level Security The approach described in this document relies on commonly shared group keying material to protect communication within a multicast group. This means that messages are encrypted at a group level (group-level data confidentiality), i.e. they can be decrypted by any member of the multicast group, but not by an external adversary or other external entities. In addition, it is required that all group members are trusted, i.e. they do not forward the content of group messages to unauthorized entities. However, in many use cases, the devices in the multicast group belong to a common authority and are configured by a commissioner. For instance, in a professional lighting scenario, the roles of multicaster and listener are configured by the lighting commissioner, and devices strictly follow those roles. Furthermore, the presented approach SHOULD take into consideration the risk of compromise of group members. Such a risk is reduced when multicast groups are deployed in physically secured locations, like lighting inside office buildings. The adoption of key management schemes for secure revocation and renewal of security contexts group keying material SHOULD be considered. 7.2. Management of Group Keying Material As stated in Section 2, it is important to adopt a group key management scheme that SHOULD update the security context and keying material in the group, before a new endpoint joins the group or after a currently present endpoint leaves the group. This is necessary in Tiloca, et al. Expires September 14, 2017 [Page 12] Internet-Draft Secure group communication for CoAP March 2017 order to preserve backward confidentiality and forward confidentiality in the multicast group. Especially in dynamic, large-scale, multicast groups where endpoints can join and leave at any time, it is important that the considered group key management scheme is efficient and highly scalable with the group size, in order to limit the impact on performance due to the security context and keying material update. 7.3. Late Joining Endpoints Upon joining the multicast group when the system is fully operative, listeners are not aware of the current sequence number values used by different multicasters to transmit multicast request messages. This means that, when such listeners receive a secure multicast message from a multicaster, they are not able to verify if that message is fresh and has not been replayed. In order to address this issue, upon receiving a multicast message from a particular multicaster for the first time, late joining listeners can initialize their last-seen sequence number in their Recipient Context associated to that multicaster. However, after that they drop the message, without delivering it to the application layer. This provides a reference point to identify if future multicast messages from the same multicaster are fresher than the last one seen. As an alternative, a late joining listener can directly contact the multicaster, and explicitly request a confirmation of the sequence number in the first received multicast message. A possible different approach considers the GM as an additional listener in the multicast group. Then, the GM can maintain the sequence number values of each multicaster in the group. When late joiners send a request to the GM to join the group, the GM can provide them with the list of sequence number values to be stored in the Recipient Contexts associated to the appropriate multicasters. 7.4. Provisioning of Public Keys Upon receiving a secure CoAP message, a recipient endpoint relies on the sender endpoint's public key, in order to verify the counter signature conveyed in the COSE Object. If not already stored in the Recipient Context associated to the sender endpoint, the recipient endpoint retrieves the public key from a trusted key repository. In such a case, the correct binding between the sender endpoint and the retrieved public key MUST be assured, for instance by means of public key certificates. Further Tiloca, et al. Expires September 14, 2017 [Page 13] Internet-Draft Secure group communication for CoAP March 2017 details about how this requirement can be fulfilled are out of the scope of this document. Alternatively, the Group Manager can be configured to store public keys of group members and provide them upon request. In such a case, upon joining a multicast group, an endpoint provides the Group Manager with its own public key, by means of the same secure channel used to carry out the join procedure. After that, the Group Manager MUST perform a proof-of-possession challenge-response with the joining endpoint, in order to verify that it actually owns the associated private key. In case of success, the Group Manager stores the received public key as associated to the joining endpoint and its endpoint ID. From then on, that public key will be available for secure and trusted delivery to other endpoints in the multicast group. Note that in simple, less dynamic, multicast groups, it can be convenient for the Group Manager to provide an endpoint upon its joining with the public keys associated to all endpoints currently present in the group. 8. IANA Considerations This document has no actions for IANA. 9. Acknowledgments The authors sincerely thank Rolf Blom, Carsten Bormann, John Mattsson and Jim Schaad for their feedback and comments. 10. References 10.1. Normative References [I-D.ietf-core-object-security] Selander, G., Mattsson, J., Palombini, F., and L. Seitz, "Object Security of CoAP (OSCOAP)", draft-ietf-core- object-security-01 (work in progress), December 2016. [I-D.ietf-cose-msg] Schaad, J., "CBOR Object Signing and Encryption (COSE)", draft-ietf-cose-msg-24 (work in progress), November 2016. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . Tiloca, et al. Expires September 14, 2017 [Page 14] Internet-Draft Secure group communication for CoAP March 2017 [RFC7252] Shelby, Z., Hartke, K., and C. Bormann, "The Constrained Application Protocol (CoAP)", RFC 7252, DOI 10.17487/RFC7252, June 2014, . [RFC7641] Hartke, K., "Observing Resources in the Constrained Application Protocol (CoAP)", RFC 7641, DOI 10.17487/RFC7641, September 2015, . 10.2. Informative References [I-D.ietf-ace-oauth-authz] Seitz, L., Selander, G., Wahlstroem, E., Erdtman, S., and H. Tschofenig, "Authentication and Authorization for Constrained Environments (ACE)", draft-ietf-ace-oauth- authz-05 (work in progress), February 2017. [I-D.seitz-ace-oscoap-profile] Seitz, L. and F. Palombini, "OSCOAP profile of ACE", draft-seitz-ace-oscoap-profile-01 (work in progress), October 2016. [I-D.selander-ace-cose-ecdhe] Selander, G., Mattsson, J., and F. Palombini, "Ephemeral Diffie-Hellman Over COSE (EDHOC)", draft-selander-ace- cose-ecdhe-04 (work in progress), October 2016. [RFC3740] Hardjono, T. and B. Weis, "The Multicast Group Security Architecture", RFC 3740, DOI 10.17487/RFC3740, March 2004, . [RFC4046] Baugher, M., Canetti, R., Dondeti, L., and F. Lindholm, "Multicast Security (MSEC) Group Key Management Architecture", RFC 4046, DOI 10.17487/RFC4046, April 2005, . [RFC4535] Harney, H., Meth, U., Colegrove, A., and G. Gross, "GSAKMP: Group Secure Association Key Management Protocol", RFC 4535, DOI 10.17487/RFC4535, June 2006, . [RFC4944] Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, "Transmission of IPv6 Packets over IEEE 802.15.4 Networks", RFC 4944, DOI 10.17487/RFC4944, September 2007, . Tiloca, et al. Expires September 14, 2017 [Page 15] Internet-Draft Secure group communication for CoAP March 2017 [RFC4949] Shirey, R., "Internet Security Glossary, Version 2", FYI 36, RFC 4949, DOI 10.17487/RFC4949, August 2007, . [RFC6282] Hui, J., Ed. and P. Thubert, "Compression Format for IPv6 Datagrams over IEEE 802.15.4-Based Networks", RFC 6282, DOI 10.17487/RFC6282, September 2011, . [RFC6347] Rescorla, E. and N. Modadugu, "Datagram Transport Layer Security Version 1.2", RFC 6347, DOI 10.17487/RFC6347, January 2012, . [RFC6749] Hardt, D., Ed., "The OAuth 2.0 Authorization Framework", RFC 6749, DOI 10.17487/RFC6749, October 2012, . [RFC7228] Bormann, C., Ersue, M., and A. Keranen, "Terminology for Constrained-Node Networks", RFC 7228, DOI 10.17487/RFC7228, May 2014, . [RFC7390] Rahman, A., Ed. and E. Dijk, Ed., "Group Communication for the Constrained Application Protocol (CoAP)", RFC 7390, DOI 10.17487/RFC7390, October 2014, . Appendix A. Group Joining Based on the ACE Framework The join process to register an endpoint as a new member of a multicast group MAY be based on the ACE framework [I-D.ietf-ace-oauth-authz] and the OSCOAP profile of ACE [I-D.seitz-ace-oscoap-profile]. With reference to the terminology defined in OAuth 2.0 [RFC6749]: o The joining endpoint acts as Client; o The Group Manager acts as Resource Server, exporting one join- resource for each multicast group it is responsible for; o An Authorization Server enables and enforces authorized access of the joining endpoint to the Group Manager and its join-resources. Then, in accordance with [I-D.seitz-ace-oscoap-profile], the joining endpoint and the Group Manager rely on OSCOAP [I-D.ietf-core-object-security] for secure communication and consider Ephemeral Diffie-Hellman Over COSE (EDHOC) Tiloca, et al. Expires September 14, 2017 [Page 16] Internet-Draft Secure group communication for CoAP March 2017 [I-D.selander-ace-cose-ecdhe] as a possible method to establish key material. The joining endpoint sends to the Group Manager an OSCOAP request to access the join-resource associated to the multicast group to join. The Group Manager replies with an OSCOAP response including the Common Context associated to that group (see Section 4). In case the Group Manager is configured to store the public keys of group members, the joining endpoint additionally provides the Group Manager with its own public key, and MAY request from the Group Manager the public keys of the endpoints currently present in the group (see Section 7.4). Both the joining endpoint and the Group Manager MUST adopt secure communication also for any message exchange with the Authorization Server. To this end, different alternatives are possible, including OSCOAP and DTLS [RFC6347]. Appendix B. List of Use Cases Group Communication for CoAP [RFC7390] provides the necessary background for multicast-based CoAP communication, with particular reference to low-power and lossy networks (LLNs) and resource constrained environments. The interested reader is encouraged to first read [RFC7390] to understand the non-security related details. This section discusses a number of use cases that benefit from secure group communication. Specific security requirements for these use cases are discussed in Section 2. o Lighting control: consider a building equipped with IP-connected lighting devices, switches, and border routers. The devices are organized into groups according to their physical location in the building. For instance, lighting devices and switches in a room or corridor can be configured as members of a single multicast group. Switches are then used to control the lighting devices by sending on/off/dimming commands to all lighting devices in a group, while border routers connected to an IP network backbone (which is also multicast-enabled) can be used to interconnect routers in the building. Consequently, this would also enable logical multicast groups to be formed even if devices in the lighting group may be physically in different subnets (e.g. on wired and wireless networks). Connectivity between ligthing devices may be realized, for instance, by means of IPv6 and (border) routers supporting 6LoWPAN [RFC4944][RFC6282]. Group communication enables synchronous operation of a group of connected lights, ensuring that the light preset (e.g. dimming level or color) of a large group of luminaires are changed at the same perceived time. This is especially useful for providing a Tiloca, et al. Expires September 14, 2017 [Page 17] Internet-Draft Secure group communication for CoAP March 2017 visual synchronicity of light effects to the user. Devices may reply back to the switches that issue on/off/dimming commands, in order to report about the execution of the requested operation (e.g. OK, failure, error) and their current operational status. o Integrated building control: enabling Building Automation and Control Systems (BACSs) to control multiple heating, ventilation and air-conditioning units to pre-defined presets. Controlled units can be organized into multicast groups in order to reflect their physical position in the building, e.g. devices in the same room can be configured as members of a single multicast group. Furthermore, controlled units are expected to possibly reply back to the BACS issuing control commands, in order to report about the execution of the requested operation (e.g. OK, failure, error) and their current operational status. o Software and firmware updates: software and firmware updates often comprise quite a large amount of data. Therefore, it can overload a LLN that is otherwise typically used to deal with only small amounts of data, on an infrequent base. Rather than sending software and firmware updates as unicast messages to each individual device, multicasting such updated data to a larger group of devices at once displays a number of benefits. For instance, it can significantly reduce the network load and decrease the overall time latency for propagating this data to all devices. Even if the complete whole update process itself is secured, securing the individual messages is important, in case updates consist of relatively large amounts of data. In fact, checking individual received data piecemeal for tampering avoids that devices store large amounts of partially corrupted data and that they detect tampering hereof only after all data has been received. Devices receiving software and firmware updates are expected to possibly reply back, in order to provide a feedback about the execution of the update operation (e.g. OK, failure, error) and their current operational status. o Parameter and configuration update: by means of multicast communication, it is possible to update the settings of a group of similar devices, both simultaneously and efficiently. Possible parameters are related, for instance, to network load management or network access controls. Devices receiving parameter and configuration updates are expected to possibly reply back, to provide a feedback about the execution of the update operation (e.g. OK, failure, error) and their current operational status. o Commissioning of LLNs systems: a commissioning device is responsible for querying all devices in the local network or a selected subset of them, in order to discover their presence, and Tiloca, et al. Expires September 14, 2017 [Page 18] Internet-Draft Secure group communication for CoAP March 2017 be aware of their capabilities, default configuration, and operating conditions. Queried devices displaying similarities in their capabilities and features, or sharing a common physical location can be configured as members of a single multicast group. Queried devices are expected to reply back to the commissioning device, in order to notify their presence, and provide the requested information and their current operational status. o Emergency multicast: a particular emergency related information (e.g. natural disaster) is generated and multicast by an emergency notifier, and relayed to multiple devices. The latters may reply back to the emergency notifier, in order to provide their feedback and local information related to the ongoing emergency. Authors' Addresses Marco Tiloca RISE SICS AB Isafjordsgatan 22 Kista SE-16440 Stockholm Sweden Email: marco.tiloca@ri.se Goeran Selander Ericsson AB Farogatan 6 Kista SE-16480 Stockholm Sweden Email: goran.selander@ericsson.com Francesca Palombini Ericsson AB Farogatan 6 Kista SE-16480 Stockholm Sweden Email: francesca.palombini@ericsson.com Tiloca, et al. Expires September 14, 2017 [Page 19]